我的学习站点

老倪的blog

跳过到主内容
欢迎来到我们的知识库
< 所有主题
Print

注料不均匀Uneven Filling

Posted
Updated
Bylaoni
可能的原因建议的解决方案Possible CauseSuggested Remedies
阀针不工作阀针粘住• 清洁或更换阀针Valve stems not functioningValve stem stuck• Clean or replace the valve stem
阀针不正确• 更换阀针。参见第 5.2.5 节。Incorrect valve stem• Replace the valve stem. Refer toSection 5.2.5.
快速排气阀粘住或故障• 清洁或更换隔膜Quick exhaust valve stuck or failed• Clean or replace diaphragm
双 Delta 型密封圈出现 故障• 更换双 Delta 型密封圈。参见第 5.2.12 节。Double  delta seals failed• Replace the double  delta seal. Refer toSection 5.2.12.
模具浇口杯磨损• 更换浇口杯MoldGate detail worn• Replace the gate detail
浇口杯损坏• 按照规格更换或重新加工浇口杯Gate detail damaged• Replace or rework the gate detail to specifications
模具温度低• 提高模具冷却液温度。Low mold temperature• Increase the mold coolant temperature.
工艺阀针反应迟缓• 增加阀针式浇口上的气压ProcessingSlow acting valve stem• Increase the air pressure on valve gates
阀针打开过慢• 更改阀针式浇口上的空气阀定时Valve stem opens late• Change the air valve timing on valve gates
热流道温度设定不正确• 调整浇道温度Hot runnerTemperature settings incorrect• Adjust the sprue temperature.
• 调整注嘴温度• Adjust the nozzle tip temperature.
• 调整分流板温度• Adjust the manifold temperature.
注嘴损坏• 更换注嘴。参见第 5.2.8 节。Nozzle tipDamaged• Replace the nozzle tip. Refer toSection 5.2.8.
注嘴不正确• 安装合适的注嘴。参见第 5.2.8.3 节。Incorrect nozzle tip• Install the proper nozzle tip. Refer toSection 5.2.8.3.
注嘴隔热帽不正确• 更换注嘴隔热帽。参见第 5.2.14 节。Incorrect nozzle tip insulator• Replace the nozzle tip insulator. Refer toSection 5.2.14.
注嘴加热器注嘴松动• 安装合适的注嘴。参见第 5.2.8.3 节。Nozzle heaterLoose nozzle tip• Install the proper nozzle tip. Refer toSection 5.2.8.3.
注嘴加热器不正确• 安装合适的注嘴加热器。参见 第 5.2.13.2 节。Incorrect nozzle heater• Install the proper nozzle heater. Refer toSection 5.2.13.2.
加热器与板接触• 调整加热器的位置Heater touching plate• Adjust the position of the heater
注嘴加热器故障• 更换Faulty nozzle heater• Replace
热电偶故障Faulty thermocouple
分流板加热器故障Faulty manifold heater
浇道加热器故障Faulty sprue heater
浇道热电偶故障Faulty sprue thermocouple
目录